Two Questions, Two Formulas
"How much anchor chain do I need" is two questions. The first is how much to let out at a given anchorage: depth plus bow height plus the rise of tide, times a scope ratio. That is the scope calculator, and the reasoning is in Anchor Scope Explained. The second is how much to buy and carry, which is the first formula run once, for the deepest water you plan to anchor in, at 7:1. That is this page. The difference matters because the second number is the one that has to fit the locker, the windlass and the bow, and it is the one people under-buy.
How Much Rode to Carry
Rode to carry = (deepest planned depth + bow height + tidal range) × 7, rounded up. Use 8 instead of 7 for a chain-and-rope rode, because rope has no catenary and needs the extra scope to keep the pull flat.
Be honest about the depth. Mediterranean cruisers rarely anchor deeper than 10 to 12 m, which at 7:1 with a 1.5 m bow and no tide is 80 to 95 m. On the west coast of Scotland, in Norway, in British Columbia or in the Pacific atolls, 20 m anchorages are normal, and 7:1 on 22 m is 155 m of chain, which almost no yacht carries. Those boats anchor at 4:1 or 5:1 in deep water and make it up with a bigger anchor and a long snubber. If your number comes out above 100 m, that is the conversation to have, not a reason to shorten the formula.
Anchor Chain Size Chart
Chain size is set by the anchor and the windlass, not by the boat directly: the chain has to fit the gypsy, and the anchor makers pair each anchor with a chain. Lewmar's pairing for the Delta, read against the boat lengths its selection chart gives each anchor, produces the bands below. Weights are Maggi's DIN 766 G30 calibrated chain figures; working load limits (WLL) likewise.
| Chain | US size | Boat length | kg/m | lb/ft | WLL (G30) | Paired anchors |
|---|---|---|---|---|---|---|
| 6 mm | 1/4 in | to 9 m / 30 ft | 0.8 | 0.54 | 5 kN / 1,120 lb | Delta 9 lb; Rocna 4 kg |
| 7 mm | 9/32 in | 9–10.5 m / 30–35 ft | 1.1 | 0.74 | 7.5 kN / 1,690 lb | Delta 14 lb |
| 8 mm | 5/16 in | 10.5–14 m / 35–46 ft | 1.4 | 0.94 | 10 kN / 2,250 lb | Delta 22 and 35 lb |
| 10 mm | 3/8 in | 14–21 m / 46–68 ft | 2.2 | 1.48 | 12.5 kN / 2,810 lb | Delta 44 to 88 lb |
| 13 mm | 1/2 in | over 21 m / 68 ft | 3.9 | 2.62 | 20 kN / 4,500 lb | Delta 110 lb and up |
Three notes. The US sizes are the nearest stock size, not an exact conversion: 5/16 in is 7.9 mm and 3/8 in is 9.5 mm, and a metric gypsy will not run imperial chain or the other way round, so buy the chain your windlass was cut for. Grade matters more than size for strength: G40 (high test) chain of the same diameter has a working load about a third higher than the G30 figures above, and G70 higher again, which is how a boat can drop one size and save weight in the bow. And heavy displacement, catamarans and boats with a lot of windage go one size up, exactly as they do for the anchor; Rocna says the same in its sizing chart.
The Load the Chain Has to Hold
The ABYC horizontal working load table, for chain rode with no snubber, puts a 35 ft boat at 900 lb in 30 knots, 1,800 lb in 42 knots and 3,600 lb in 60; a 50 ft boat at 1,600, 3,200 and 6,400 lb. Against those, 8 mm G30 chain has a working load limit of 10 kN, about 2,250 lb, and a breaking load four times that. The chain is rarely the weak link. The shackle between chain and anchor, the swivel if there is one, the bow roller and the cleat the snubber is on fail first, and a rope snubber cuts the shock loads by a factor of about three. The calculator shows the margin between your chain's WLL and the 30-knot ABYC load for your length so you can see when a size up is worth its weight.
Chain and Rope
A mixed rode is lighter, cheaper, kinder to the bow and, with enough scope, holds as well. It needs chain at the anchor end: at least one boat length, never less than about 10 m, for the catenary in the first metres and for chafe on rock and coral. The rope should be three-strand or eight-plait nylon, which stretches and absorbs the snatch that chain passes straight to the anchor, spliced to the chain through a thimble or a proper chain splice so it runs through the gypsy. Add one to the scope ratio and inspect the splice every season.
Marking the Chain
A rode you cannot measure as it runs out is a scope you are guessing. Mark it every 10 m (or 25 ft) with paint, coloured cable ties through the links, or chain markers, and write the code on the inside of the locker lid. Ships count in shots of 90 ft (15 fathoms), British yachts in shackles of the same 27.5 m; the calculator shows how many shackles your rode is because the old pilot books still talk that way.
Where the Figures Come From
- Chain weights and working load limits: Maggi Group, DIN 766 G30 calibrated chain specification table, read 3 November 2026.
- Chain size by anchor: Lewmar's Delta anchor specification sheet (recommended chain size per anchor weight) and its selection guide by boat length; Rocna's sizing page for the 6 to 16 mm range.
- Horizontal working loads: the ABYC table as published on Mantus Marine's anchor sizing page.
- Rode-to-carry and chain-in-a-mixed-rode rules: standard cruising practice, set out in Anchor Scope Explained.